The product description

This product is a one-component silicone elastomer that can be cured by contact with moisture in the air at room temperature.

 Dealcoholized, neutral

 Not flowing, thixotropic

 White, black, gray

 Self-adhesive (no primer)

Product advantages

As a room temperature neutral curing elastomer can be used to ensure that the neutral, non-corrosive metal (such as copper) electronic components.

 odorless, more acceptable in the operating environment.

 has excellent bonding properties for all kinds of surfaces.

 Excellent thermal stability (-65~185℃).

 Excellent mechanical properties.

application

This product is developed for professional customers. As an elastic adhesive, it can be used for sealing and bonding between different materials with thermal stress, such as glass, metal or plastic with high thermal stability.

 General industrial maintenance and repair

 Sealing & bonding of metal parts

 Sealing & bonding of engineering plastic parts

Especially suitable for high performance or neutral bonding without undercoat.

 Electronic appliances

 Bonding of automobile headlights

 Solar panels

 It is chemically neutral and bonded under hot and humid conditions, making it an ideal protection product.

Typical property

1. Characteristics of uncured products

Look........................ . .......................................... Do not flow paste

Smell....................................................................... Alcohol type

Color...................................................................... White, black, gray

Liquidity...................... < 2mm(Refer to Boeing S 7502 -- NMRPS 459)

Specific gravity at 25℃…………………………1.3

Extrusion rate, g/min……………………………130

(Refer to standard NMRPS 495A 3mm/3bars)

2. When curing

This product starts to solidify after contact with moisture in the air. The curing rate increases with increasing temperature and humidity.

23℃, 50% Rh, crusting time, min…………… . ...... . 10 ~ 15

Time required for 2mm curing thickness, h... .............................. 8

The curing thickness after 24h, mm………………………3.5

23℃, 50%RH, surface drying time, min…………… . ...... . 40

3. Product performance after curing

The 2mm film was cured at 23℃×50%RH for 7 days.

Shore hardness Α dot 34

(Refer to ISO R 868, DIN 53505, ASTM D2240,

NF T 46003, NMRPS 471, BS 903 Part A2)

100% constant extension modulus, Mpa ………………………0.84

(Refer to ISO R 37 (H2), DIN 53504, ASTM D 412,

NFT 46002 (H2), NMRPS 470, BS 903 Part A2)

Tensile strength, Mpa …………………………………………3.31.

(Refer to ISO R 37 (H2), DIN 53504, ASTM D 412,

NFT 46002 (H2), NMRPS 470, BS 903 Part A2)

Fracture elongation, %………………………………………510

(Refer to ISO R 37 (H2), DIN 53504, ASTM D 412,

NFT 46002 (H2), NMRPS 470, BS 903 Part A2)

Tearing strength, kN/m………………………………15

(Referred to Standard ASTM D 624 Specimen A, NMRPS 492)

4. Thermal performance (2mm film thickness)

The lower limit of using temperature is ……… To 60℃(brittle point)

Maximum temperature for continuous use …………………+ 150℃

(Maximum temperature at 1000h)

Maximum instantaneous service temperature …………… . + 185℃

(Maximum temperature at 72h)

Note: Mechanical properties and Shore hardness A were measured before and after thermal aging. These service temperatures are not absolute limits; they represent the temperature range at which the mechanical properties are reduced to more than 50% of the initial value. If not continuous 72 hours, instantaneous can withstand higher temperatures.

5. Adhesive performance

After 14 days of curing at 23℃×50%RH, the shear strength of 1mm specimen thickness at the joint was obtained according to the standard NM748.

Glass, MPa.................................................................. 1.3 AG3aluminum, MPA ………………………………………………………… 1.2

Stainless steel/glass, MPA ………………………… ......... 1.5

Nylon 66 containing 30% glass fiber, Mpa ……………………………1.3

PC, ABS, PBT, epoxy-PES, MPA ………… . ........................ 1.2

Damage type ………………………………………………… . 100% Cohesion destruction

This product can also be a bottomless coating bonding a variety of substrates such as: enamel, spray steel, cast iron, and are 100% cohesive destruction.

Product process

This product can be "ready to use", so the use process is relatively simple. It can be operated manually or automatically by equipment.

The product is applied to one of the two joint surfaces to be bonded before the skin is formed.

It is recommended to apply this product on a clean and dry surface. Do not apply immediate pressure to the joint.

Packaging

 310 ml pens

25 kg a barrel

260 kg buckets

storage

In the unopened state, it should be stored at 2°C ~ 30°C, and can be used within 12 months from the production date.